Miller SpectrumICE-40T Torch Instrukcja Właściciela

ProcessesDescriptionAir Plasma Cuttingand GougingAir Plasma CutterOM-237 974C 2010−04Spectrum 625 X-TREMEAnd ICE-40T TorchRFile: Plasma CuttersVisit o

OM-237 974 Page 6D Avant d’effectuer les connexions d’alimentation, vous devez relierle bon fil de terre.D Les câbles doivent être exempts d’humidité,

OM-237 974 Page 7D Ne coupez pas dans un endroit près d’opérations de décapage, denettoyage ou de vaporisation. La chaleur et les rayons d’arc peu-ven

OM-237 974 Page 8Les CHAMPS ÉLECTROMAGNÉTIQUES (CEM)peuvent affecter les implants médicaux.D Les porteurs de stimulateurs cardiaqueset autres implants

OM-237 974 Page 92-4. Proposition californienne 65 AvertissementsLes équipements de soudage et de coupage produisent desfumées et des gaz qui contienn

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 10SECTION 3 − DEFINITIONS3-1. Symbols And Definitions For Nameplate And Ser

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 11SECTION 4 − INSTALLATION4-1. SpecificationsPower SupplyInputRated AC phas

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 124-2. Duty Cycle And OverheatingDuty Cycle is percentage of 10 min-utes th

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 134-5. Connecting Gas/Air Supply805 326-A. Use only clean, dry air with 90t

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 144-7. Electrical Service GuideFailure to follow these electrical service g

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 154-9. Serial Number And Rating Label LocationThe serial number and rating

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 164-11. Wiring Optional 240 Volt Plug (119 172) For Connection To Bobcat, T

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 174-12. Installing Alternative Plug1 Supplied 230 VAC PlugCut cord close to

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 18SECTION 5 − OPERATION5-1. Controls1 Output ControlUse control to set cutt

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 195-2. Mild Steel Recommended Cut Speed. Aluminum and stainless steel cut s

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 20Ref. 803 640-A / 801 400-B / Ref. 802 8785-4. Plasma Cutting System Pract

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 21out bottom of cut.Ref. 803 640-A / 801 400-B5-5. Sequence Of Cutting Oper

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 22Ref. 803 640-A / 801 400-B5-6. Sequence Of Gouging OperationConnect work

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 23Ref. 803 640-A / 801 400-B5-7. Sequence Of Piercing OperationMaintain app

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 24SECTION 6 − MAINTENANCE & TROUBLESHOOTING6-1. Routine Maintenance! Di

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 256-2. Wrapper RemovalRef. 8805 326-A! Turn off power, anddisconnect input

2TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1...1-1. Symbol Usage 1...

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 266-3. Checking Or Replacing Filter Element! Turn power Off, and discon-nec

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 276-4. Status/Trouble Lights. Diffculty establishing a pilot arc may indica

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 286-6. Checking/Replacing Retaining Cup, Tip, And Electrode! Overtightening

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 296-7. Troubleshooting Power SourceTrouble RemedyNo pilot arc; difficulty i

. A complete Parts List is available at www.MillerWelds.comOM-237 974 Page 306-8. Troubleshooting TorchTrouble RemedyArc goes on and off while cutting

OM-237 974 Page 31Notes

OM-237 974 Page 32SECTION 7 − ELECTRICAL DIAGRAMFigure 7-1. Circuit Diagram

OM-237 974 Page 33235 080-A

OM-237 974 Page 34SECTION 8 − PARTS LIST8-1. Recommended Spare PartsDescriptionPartNo.Dia.Mkgs.ItemNo.Recommended Spare PartsQuantity211120 LABEL, ICE

OM-237 974 Page 351 183 427 Handle Assy, complete (1)2 192 059 Main Body (1)3 185 833 Switch Assembly w/spring (1)4 190 220 Spring, trigger assembly5

Notes

Notes

Notes

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 2010−01Your distributor also givesyou ...ServiceYou always get the

ORIGINAL INSTRUCTIONS − PRINTED IN USA © 2010 Miller Electric Mfg. Co. 2010−01Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer

OM-237 974 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGpom_2010−03Protect yourself and others from injury — read and follow these precaut

OM-237 974 Page 2SIGNIFICANT DC VOLTAGE exists ininverter power sources AFTER the re-moval of input power.D Turn Off unit, disconnect input power, che

OM-237 974 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceHOT PARTS can burn.D Do not touch hot parts bare handed.D Allow c

OM-237 974 Page 41-4. California Proposition 65 WarningsWelding or cutting equipment produces fumes or gaseswhich contain chemicals known to the State

OM-237 974 Page 5SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANTUTILISATIONpom_2010−03freSe protéger et protéger les autres contre le risque de bless